Sign in or Register


Edustream Sdn Bhd
11, Jalan Perniagaan Setia 9,
Taman Perniagaan Setia,
81100 Johor Bahru,
Johor, Malaysia.
+607-562 7331
+607-562 7335

STEM DIY Tooling Jeep Project KJ-601

Previous 12 / 12 Next

STEM DIY Tooling Jeep Project KJ-601 Accessories Science Education STEM DIY Tooling Jeep Project KJ-601 Accessories Science Education
RM 11.00
SKU: 6971580586014
In Stock


Suitable for education such as: science, technology, engineering

  1. Glue the four small wooden blocks with wood glue, put on the axles, and glue them to the base of the car. Glue the four small wooden blocks on the right side and fix them on the roof of the car. Let the glue dry for about ten minutes.
  2. Clamp the axle in place and place it on the axle, leaving a little gap so that the wheels can rotate flexibly when they are moving.
  3. Install the wheels in.
  4. Use double-sided tape to fix the battery box and motor on the board of the car bullet base. The head of the motor should be exposed and the position should be left. Then, the fan blades should be installed. The small holes of the metal sheet can be wound).
  5. Glue the roof of the car to the base of the car.
  6. Install the propeller to the motor, install 2 AA batteries, press the metal piece (switch) on the battery box, and the car will start (as shown in the figure, the car runs backwards, just replace the left and right connecting wires on the motor) Up).

 

Sesuai untuk pendidikan seperti: sains, teknologi, kejuruteraan

Langkah percubaan pemasangan Jeep:

  1. Lekatkan empat bongkah kayu kecil dengan gam kayu, letakkan pada gandar, dan gamkannya pada pangkal kereta. Lekatkan empat bongkah kayu kecil di sebelah kanan dan pasangkannya di atas bumbung kereta. Biarkan gam kering selama kira-kira sepuluh minit.
  2. Kepit gandar pada tempatnya dan letakkan pada gandar, tinggalkan sedikit jurang supaya roda boleh berputar secara fleksibel apabila ia bergerak.
  3. Pasang roda masuk.
  4. Gunakan pita dua sisi untuk membetulkan kotak bateri dan motor pada papan kayu dasar peluru kereta. Kepala motor hendaklah didedahkan dan kedudukannya hendaklah dikhaskan. Kemudian, bilah kipas hendaklah dipasang. Lubang-lubang kecil kepingan logam boleh luka).
  5. Lekatkan bumbung kereta ke pangkal kereta.
  6. Pasang kipas pada motor, pasang 2 bateri AA, tekan kepingan logam (suis) pada kotak bateri, dan kereta akan dihidupkan (seperti yang ditunjukkan dalam rajah, kereta berjalan ke belakang, hanya tukar wayar penyambung kiri dan kanan pada motor) Atas).

 

适用于教育例如:科学,技术,工程

吉普车拼装实验步骤:

  1. 把四个孔的小木块粘上木工胶,套上车轴,粘在车的底座上,右边把四小跟木块粘上胶,固定在车的顶板上,晾晒十分钟左右,让胶水干。
  2. 把车轴卡位,卡在车轴上,留一点缝隙,让轮子活动的时候可以灵活的转动。
  3. 把车轮安装进去。
  4. 用双面胶将电池盒和电机固定在车子弹底座木板上,电机的头要露出来,位置要留出来,等下要安装扇叶(电机和电池盒的解法,电池盒的线穿过电机的金属片小孔缠绕就可以了)。
  5. 把车的顶棚粘在车的底座上。
  6. 把螺旋桨安装到电机上,装上2节5号电池,按下电池盒上的金属片(开关),车子就会启动(如图车子往后跑,电机上的连接线的左右换下就可以了)。

 


 Contact Us 

We're here to help and answer any question u might have. We look forward to hearing from you.

You have 0 items in you cart. Would you like to checkout now?
0 items
Switch to Mobile Version
available in